Learning how to install garage door torsion springs in Bergen County is an important skill. Many people choose to install torsion springs by themselves. Torsion springs that are mishandled or improperly installed can be dangerous. Do not install these by yourself unless you are equipped with the precise tools, experience and mechanical aptitude. You will require the following materials for installing your torsion springs:
- 2 box wrenches- size 9/16”
- 2, ½” diameter, cold rolled winding bars steel, 18” long
- 7/16” socket wrench
- Locking pliers
- Wood anchor pads
- Prepare the frame of the door
Before starting, ensure that a torsion spring assembly is securely and firmly attached to your garage frame. It is suggested to make the anchor pad of wood using the Grade 2 yellow pine or better. Other acceptable wood choices include oak, hickory, birch and beech. Ensure that the wood is crack and splits free. Avoid using wood that is labeled as SPF or spruce-pine-fir.
- Assemble torsion spring to the spring-tube
Keep the door locked and in down mode securely, using locking pliers or a door lock. This step must be taken in order to avoid the door from opening prematurely and causing you injury.
Your door may have either one or two torsion springs. Spring coils, a stationary cone and a winding cone are located within each torsion spring. Sometimes the spring coils can be color coded in either black or red. The color helps to recognize the side of the door on which the torsion spring must be assembled. Black winding torsion spring is assembled on door’s right side and red winding torsion springs are placed on door’s left side, when you view the garage door from inside out. If you fail to put the correct torsion spring on the proper side, it will result in injury.
- Attach the mounting plates onto the door frame
Attach the foot of end-bearing plate at a horizontal angle with 2 long hex-head bolts and bolts. Ensure that you are using the bottom 2 slots of the horizontal track with 12 inch radius and 2 upper slots of the horizontal track with 15 inch radius. Attach the wall flange to end-bearing plates on wood jamb using a long lag screw. On the 12 inch radius horizontal tracks, every end-bearing plate must be attached with nuts and carriage bolts.
- Attached the torsion spring to the mounting plates
With the help of a helper, lift the torsion spring tube association and place the tube ends in the bearing into end-bearing plates. After leveling the tubes, place the center-bearing plate on the anchor-pad long lag and red-coated bolts and screws.
NOTE: Red-headed fasteners must be installed for the attachment of center bearing plate to indicate this part will be under extreme tension once spring is wound (FIG. TOR-5)
- Install the torsion spring cables
There is a cable which is close to the bracket at the bottom is between the roller shafts and wall to cable drum. The cable is put in the nick of the cable drum. Turn the cable drum and slide it up tight against the other end-bearing plate. This will remove the cable slack. Ensure that the cable thoroughly follows grooves in the cable drum.
- Adjust the torsion springs with winding bars
Draw a straight line the dimension of the spring with a chalk. This will show the number of turns required on the springs. Insert the two winding-bars completely into a winding cone. Then wind the springs for ¼ turn in the upward direction. Refrain from using screwdriver for a winding bar. Secure the spring with set screws. Doors that have two torsion springs, usually have the same number of turns. Then remove the locking pliers.
- Test the door function
Unlock the garage door and raise it halfway. If the tracks are misaligned or the back hangers are weak, the door will fall. The horizontal tracks must be parallel. The lag screws should be securely fastened.
- Final adjustments
Put the door on the lock in the down position before adjusting the torsion spring tension. Using locking pliers, clamp the torsion spring. Use the winding bars to wind the spring and increase the tension. You will reduce the tension every time you remove a turn.
Learning how to install garage door springs in Bergen County is a great skill. Ensure you have the proper tools, skills, experience and support to carry it out. If you are not sure of your skills, it is recommended to hire garage door spring maintenance experts to ensure precision in local garage door repair in Bergen County